Startup & storage
iPod frozen
Frozen screen, buttons not responding, or stuck on a message? Reset it first. Pick what happens and your model to see the likely causes when it keeps freezing.
What exactly happens?
Which iPod do you have?
Most common causes, by model
Also searched as is frozen · freezes · unfreeze iPod · frozen screen · unfreeze an iPod · fix a frozen iPod · unfreeze my iPod · not responding · fix frozen iPod · keeps freezing · screen frozen · screen not responding · fix frozen screen · has frozen how do i unfreeze it · screen is frozen · screen freezes · unfreeze your iPod · screen freeze · frozen locked · unfreeze screen
Reset it first: a reset does not erase your songs. If it still won't respond, charge it for at least 30 minutes. An iPod that keeps freezing most often has a failing hard drive; a restore fixes it when the software is damaged. On the 4th Gen and Photo, check the hard drive cable first, then the drive: our Hard Drive Repair Service is probably the best first option. On the other models, a drive failure is the ideal time for a flash upgrade.
Free checks first
- 3rd Gen or Photo showing a disk with a magnifying glass and a progress bar? It is checking its drive (15 to 20 minutes), not frozen: leave it on power.
- If it still shows up on a computer, copy your music off before anything else (copy the whole iPod_Control folder to keep more than the songs); if it clicks or drops off the computer while copying, stop and get it diagnosed.
- Put the Hold switch firmly in the unlocked position. A locked iPod ignores every button.
- Reset it: press and hold Menu and the center (Select) button for 8 seconds, or until the Apple logo appears. If that fails, put the iPod on a table and press the center button without touching the wheel.
- Reset the 3rd Gen: hold Menu and Play/Pause until the Apple logo appears.
- Leave it on the charger for at least 30 minutes: a very empty battery has to charge before the iPod can start.
- On the 3rd Gen, charge from a FireWire charger or a 6-pin FireWire port on a computer that is on and awake: its USB cable syncs but never charges it.
- Hold the iPod up to your ear: unusual clicking patterns are a strong sign that the hard drive is failing.
- Check the hard drive's health in Diagnostic Mode: on a healthy drive the reallocated sectors (reallocs) and pending sectors read zero or close to it. A high number, or numbers that rise each time you check, mean the drive is failing; pending sectors are the sharper warning.
iPod Classic (A1238) frozeniPod Classic 6th Gen (A1238) frozeniPod Classic 7th Gen (A1238) frozen
Most likely: Failing hard driveNext: Loose or damaged hard drive cable · 1 more cause
-
Most likely
Failing hard drive
Repeated clicking (the click of death: click, click, whir, or grinding) or the red X usually mean the hard drive is failing. A failed drive is the ideal time for a flash upgrade: flash storage has no heads, platters or motor, so the clicking, stalling and seizing that end an old hard drive can't happen. If your old drive still reads, add our music transfer ($149) and we copy everything on it onto the new flash storage.
Replacement Hard Drive
For the iPod Classic 6th Gen
80GB · 120GB · 160GB
128GB Flash Mod Service (installed by iMods)
For the iPod Classic 6th Gen
Replaces the hard drive with flash memory: silent, no moving parts
Replacement Hard Drive 160GB (Late 2009)
For the iPod Classic 7th Gen
Flash Mod Service (installed by iMods)
For the iPod Classic 7th Gen
Replaces the hard drive with flash memory: silent, no moving parts
Step-by-step guide iPod Classic 6th/7th Gen hard drive replacement (11 steps)
-
Next most likely
Loose or damaged hard drive cable
A loose or damaged hard drive cable can make the drive click, drop out or show the red X. Unless the problem started after a repair, the cable itself is rarely the fault on the 6th and 7th Gen: if the hard drive isn't to blame, the logic board is just as likely as the cable.
Free check first Push the cable back in first; replace it only if that does not help.
Hard Drive Cable
For the iPod Classic 6th Gen
Thin · Thick
Hard Drive ZIF Ribbon Cable
For the iPod Classic 7th Gen
-
Also possible
Damaged iPod software
The iPod's software is damaged, so it can't start properly or keeps freezing. Restoring it puts fresh software on it; a restore erases the songs on the iPod.
Free check first If it still shows up on a computer, copy your music off first, then restore it with iTunes (or Finder on a Mac with macOS Catalina or later). If the restore fails, or the problem comes back, the hard drive is the likely fault.
iPod Video (A1136) frozeniPod Video 5th Gen (A1136) frozen
Most likely: Failing hard driveNext: Loose or damaged hard drive cable · 1 more cause
-
Most likely
Failing hard drive
Repeated clicking (the click of death: click, click, whir, or grinding) or the sad iPod face usually mean the hard drive is failing. A failed drive is the ideal time for a flash upgrade: flash storage has no heads, platters or motor, so the clicking, stalling and seizing that end an old hard drive can't happen. If your old drive still reads, add our music transfer ($149) and we copy everything on it onto the new flash storage.
Flash Mod Service (installed by iMods)
Replaces the hard drive with flash memory: silent, no moving parts
Step-by-step guide iPod Video 5th Gen hard drive replacement (14 steps)
-
Next most likely
Loose or damaged hard drive cable
A loose or damaged hard drive cable can make the drive click, drop out or show the sad iPod face. Unless the problem started after a repair, the cable itself is rarely the fault on the iPod Video: if the hard drive isn't to blame, the logic board is just as likely as the cable.
Free check first Push the cable back in first; replace it only if that does not help.
-
Also possible
Damaged iPod software
The iPod's software is damaged, so it can't start properly or keeps freezing. Restoring it puts fresh software on it; a restore erases the songs on the iPod.
Free check first If it still shows up on a computer, copy your music off first, then restore it with iTunes (or Finder on a Mac with macOS Catalina or later). If the restore fails, or the problem comes back, the hard drive is the likely fault.
iPod 4th Gen or iPod Photo (A1059 and A1099) frozeniPod 4th Gen (A1059) frozeniPod Photo (A1099) frozen
Most likely: Loose or damaged hard drive cableNext: Failing hard drive · 1 more cause
-
Most likely
Loose or damaged hard drive cable
On the 4th Gen and Photo, an iPod that seems too weak to spin up its hard drive often has a hard drive cable problem. A loose or damaged hard drive cable can make the drive click, drop out or show the sad iPod face. A cable fault sounds like click, whir; a failing drive sounds more like click, click, whir.
Free check first Clean the hard drive cable's contacts with 99% isopropyl alcohol (IPA) and re-seat it first; if that fails, it's likely a bad hard drive (our Hard Drive Repair Service is probably the best first option).
Hard Drive IDE Ribbon Cable
For the iPod Photo
-
Next most likely
Failing hard drive
Repeated clicking (the click of death: click, click, whir, or grinding) or the sad iPod face usually mean the hard drive is failing. Flash storage is the silent alternative to a new drive. On the 4th Gen and Photo we can often fix the hard drive without replacing it, and in most cases all songs are saved.
Hard Drive Repair Service
For the iPod 4th Gen
Mail it in: we repair your drive, and in most cases your songs are saved
Hard Drive Repair Service
For the iPod Photo
Mail it in: we repair your drive, and in most cases your songs are saved
Replacement Hard Drive
For the iPod 4th Gen
20GB · 40GB
Flash Mod Service (installed by iMods)
For the iPod 4th Gen
Replaces the hard drive with flash memory: silent, no moving parts
Replacement Hard Drive
For the iPod Photo
20GB · 30GB · 40GB · 60GB
Flash Mod Service (installed by iMods)
For the iPod Photo
Replaces the hard drive with flash memory: silent, no moving parts
Step-by-step guide iPod 4th Gen and iPod Photo hard drive replacement (12 steps)
-
Also possible
Damaged iPod software
The iPod's software is damaged, so it can't start properly or keeps freezing. Restoring it puts fresh software on it; a restore erases the songs on the iPod.
Free check first If it still shows up on a computer, copy your music off first, then restore it with iTunes (or Finder on a Mac with macOS Catalina or later). On the 4th Gen and iPod Photo the restore can stop at a picture of a plug: connect it to a wall charger to finish. Generic or incompatible wall chargers don't always give the iPod the right voltage: Apple's A1070 wall charger works with every model and is the ideal choice. If the restore fails, or the problem comes back, the hard drive cable, then the hard drive, is the likely fault (our Hard Drive Repair Service is probably the best first option).
iPod Mini (A1051) frozeniPod Mini 1st Gen (A1051) frozeniPod Mini 2nd Gen (A1051) frozen
Most likely: Failed microdrive (the Mini's hard drive)Next: Loose or damaged hard drive cable · 1 more cause
-
Most likely
Failed microdrive (the Mini's hard drive)
When the Mini's tiny hard drive (the microdrive) fails, it shows the sad iPod face or a folder icon, or makes clicking noises. Replace it with a used original microdrive, or upgrade to flash: a failed drive is the ideal time for it. Flash storage has no heads, platters or motor, so the clicking, stalling and seizing that end an old hard drive can't happen. If your old drive still reads, add our music transfer ($149) and we copy everything on it onto the new flash storage.
Replacement Microdrive (4GB)
For the iPod Mini 1st Gen
Flash Mod Service (installed by iMods)
For the iPod Mini 1st Gen
Replaces the hard drive with flash memory: silent, no moving parts
Replacement Microdrive
For the iPod Mini 2nd Gen
4GB · 6GB
Flash Mod Service (installed by iMods)
For the iPod Mini 2nd Gen
Replaces the hard drive with flash memory: silent, no moving parts
Step-by-step guide iPod Mini 1st/2nd Gen hard drive (Microdrive) replacement (13 steps)
-
Next most likely
Loose or damaged hard drive cable
A loose or damaged hard drive cable can make the drive click, drop out or show the sad iPod face. Unless the problem started after a repair, the cable itself is rarely the fault on the Mini: if the microdrive isn't to blame, the logic board is just as likely as the cable.
Free check first Push the cable back in first; replace it only if that does not help.
Hard Drive Cable
For the iPod Mini 1st Gen
Hard Drive Ribbon Cable
For the iPod Mini 2nd Gen
-
Also possible
Damaged iPod software
The iPod's software is damaged, so it can't start properly or keeps freezing. Restoring it puts fresh software on it; a restore erases the songs on the iPod.
Free check first If it still shows up on a computer, copy your music off first, then restore it with iTunes (or Finder on a Mac with macOS Catalina or later). On the Mini 1st Gen the restore can stop at a picture of a plug: connect it to a wall charger to finish. Generic or incompatible wall chargers don't always give the iPod the right voltage: Apple's A1070 wall charger works with every model and is the ideal choice. If the restore fails, or the problem comes back, the hard drive (Mini: microdrive) is the likely fault.
iPod 3rd Gen (A1040) frozeniPod 3rd Gen (A1040) frozen
Most likely: Failing hard driveNext: Loose or damaged hard drive cable · 1 more cause
-
Most likely
Failing hard drive
Repeated clicking (the click of death: click, click, whir, or grinding) or the sad iPod face usually mean the hard drive is failing. A failed drive is the ideal time for a flash upgrade: flash storage has no heads, platters or motor, so the clicking, stalling and seizing that end an old hard drive can't happen. If your old drive still reads, add our music transfer ($149) and we copy everything on it onto the new flash storage.
Replacement Hard Drive
10GB · 15GB · 20GB · 30GB · 40GB
Flash Mod Service (installed by iMods)
Replaces the hard drive with flash memory: silent, no moving parts
Step-by-step guide iPod 3rd Gen hard drive replacement (14 steps)
-
Next most likely
Loose or damaged hard drive cable
A loose or damaged hard drive cable can make the drive click, drop out or show the sad iPod face. Unless the problem started after a repair, the cable itself is rarely the fault on the 3rd Gen: if the hard drive isn't to blame, the logic board is just as likely as the cable.
Free check first Push the cable back in first; replace it only if that does not help.
Hard Drive IDE Ribbon Cable
-
Also possible
Damaged iPod software
The iPod's software is damaged, so it can't start properly or keeps freezing. Restoring it puts fresh software on it; a restore erases the songs on the iPod.
Free check first If it still shows up on a computer, copy your music off first, then restore it with iTunes (or Finder on a Mac with macOS Catalina or later). On the 3rd Gen the restore can stop at a picture of a plug: connect it to its FireWire wall charger to finish. Generic or incompatible wall chargers don't always give the iPod the right voltage: Apple's A1070 wall charger works with every model and is the ideal choice. If the restore fails, or the problem comes back, the hard drive is the likely fault.
More causes on this page, depending on what happens
6 causes, listed by what happens to your iPod
- Battery too weak to spin up the hard driveFrozen on Apple logo · not on the iPod 4th Gen or iPod Photo
- Broken Hold switchStuck on language screen
- Logic board (headphone jack connector)Stuck on language screen
- Headphone jack cable keeping it lockedStuck on language screen · iPod 4th Gen and iPod Photo only
- Hard drive cable not fully in, or a latch left openStarted after a repair or part swap
- A connector not seated after the repairStarted after a repair or part swap
Freezes iTunes
Also searched as iTunes freezes when connecting · freezes iTunes when plugged in · iTunes freezes when iPod is connected · iTunes freezes when i plug in · iTunes not responding when connected · iTunes freezing when connected · iTunes freezes when i connect · iTunes hangs when connected · iTunes freezes when plugged in · iTunes freezes when plugging in
iTunes stops responding while the iPod is connected.
Free checks first
- Plug it straight into a USB port on the computer, not a keyboard or a hub, and unplug other USB devices. If the error comes back, try another Apple cable and another USB port, restart the computer, update iTunes, and check the computer's security software.
- Hold the iPod up to your ear: unusual clicking patterns are a strong sign that the hard drive is failing.
- Check the hard drive's health in Diagnostic Mode: on a healthy drive the reallocated sectors (reallocs) and pending sectors read zero or close to it. A high number, or numbers that rise each time you check, mean the drive is failing; pending sectors are the sharper warning.
iPod Classic 6th and 7th GeniPod Classic 6th GeniPod Classic 7th Gen
Most likely: Failing hard driveNext: Loose or damaged hard drive cable
-
Most likely
Failing hard drive
Repeated clicking (the click of death: click, click, whir, or grinding) or the red X usually mean the hard drive is failing. A failed drive is the ideal time for a flash upgrade: flash storage has no heads, platters or motor, so the clicking, stalling and seizing that end an old hard drive can't happen. If your old drive still reads, add our music transfer ($149) and we copy everything on it onto the new flash storage.
Replacement Hard Drive
For the iPod Classic 6th Gen
80GB · 120GB · 160GB
128GB Flash Mod Service (installed by iMods)
For the iPod Classic 6th Gen
Replaces the hard drive with flash memory: silent, no moving parts
Replacement Hard Drive 160GB (Late 2009)
For the iPod Classic 7th Gen
Flash Mod Service (installed by iMods)
For the iPod Classic 7th Gen
Replaces the hard drive with flash memory: silent, no moving parts
Step-by-step guide iPod Classic 6th/7th Gen hard drive replacement (11 steps)
-
Next most likely
Loose or damaged hard drive cable
A loose or damaged hard drive cable can make the drive click, drop out or show the red X. Unless the problem started after a repair, the cable itself is rarely the fault on the 6th and 7th Gen: if the hard drive isn't to blame, the logic board is just as likely as the cable.
Free check first Push the cable back in first; replace it only if that does not help.
Hard Drive Cable
For the iPod Classic 6th Gen
Thin · Thick
Hard Drive ZIF Ribbon Cable
For the iPod Classic 7th Gen
iPod Video 5th GeniPod Video 5th Gen
Most likely: Failing hard driveNext: Loose or damaged hard drive cable
-
Most likely
Failing hard drive
Repeated clicking (the click of death: click, click, whir, or grinding) or the sad iPod face usually mean the hard drive is failing. A failed drive is the ideal time for a flash upgrade: flash storage has no heads, platters or motor, so the clicking, stalling and seizing that end an old hard drive can't happen. If your old drive still reads, add our music transfer ($149) and we copy everything on it onto the new flash storage.
Flash Mod Service (installed by iMods)
Replaces the hard drive with flash memory: silent, no moving parts
Step-by-step guide iPod Video 5th Gen hard drive replacement (14 steps)
-
Next most likely
Loose or damaged hard drive cable
A loose or damaged hard drive cable can make the drive click, drop out or show the sad iPod face. Unless the problem started after a repair, the cable itself is rarely the fault on the iPod Video: if the hard drive isn't to blame, the logic board is just as likely as the cable.
Free check first Push the cable back in first; replace it only if that does not help.
iPod 4th Gen and iPod PhotoiPod 4th GeniPod Photo
Most likely: Loose or damaged hard drive cableNext: Failing hard drive
-
Most likely
Loose or damaged hard drive cable
On the 4th Gen and Photo, an iPod that seems too weak to spin up its hard drive often has a hard drive cable problem. A loose or damaged hard drive cable can make the drive click, drop out or show the sad iPod face. A cable fault sounds like click, whir; a failing drive sounds more like click, click, whir.
Free check first Clean the hard drive cable's contacts with 99% isopropyl alcohol (IPA) and re-seat it first; if that fails, it's likely a bad hard drive (our Hard Drive Repair Service is probably the best first option).
Hard Drive IDE Ribbon Cable
For the iPod Photo
-
Next most likely
Failing hard drive
Repeated clicking (the click of death: click, click, whir, or grinding) or the sad iPod face usually mean the hard drive is failing. Flash storage is the silent alternative to a new drive. On the 4th Gen and Photo we can often fix the hard drive without replacing it, and in most cases all songs are saved.
Hard Drive Repair Service
For the iPod 4th Gen
Mail it in: we repair your drive, and in most cases your songs are saved
Hard Drive Repair Service
For the iPod Photo
Mail it in: we repair your drive, and in most cases your songs are saved
Replacement Hard Drive
For the iPod 4th Gen
20GB · 40GB
Flash Mod Service (installed by iMods)
For the iPod 4th Gen
Replaces the hard drive with flash memory: silent, no moving parts
Replacement Hard Drive
For the iPod Photo
20GB · 30GB · 40GB · 60GB
Flash Mod Service (installed by iMods)
For the iPod Photo
Replaces the hard drive with flash memory: silent, no moving parts
Step-by-step guide iPod 4th Gen and iPod Photo hard drive replacement (12 steps)
iPod Mini 1st and 2nd GeniPod Mini 1st GeniPod Mini 2nd Gen
Most likely: Failed microdrive (the Mini's hard drive)Next: Loose or damaged hard drive cable
-
Most likely
Failed microdrive (the Mini's hard drive)
When the Mini's tiny hard drive (the microdrive) fails, it shows the sad iPod face or a folder icon, or makes clicking noises. Replace it with a used original microdrive, or upgrade to flash: a failed drive is the ideal time for it. Flash storage has no heads, platters or motor, so the clicking, stalling and seizing that end an old hard drive can't happen. If your old drive still reads, add our music transfer ($149) and we copy everything on it onto the new flash storage.
Replacement Microdrive (4GB)
For the iPod Mini 1st Gen
Flash Mod Service (installed by iMods)
For the iPod Mini 1st Gen
Replaces the hard drive with flash memory: silent, no moving parts
Replacement Microdrive
For the iPod Mini 2nd Gen
4GB · 6GB
Flash Mod Service (installed by iMods)
For the iPod Mini 2nd Gen
Replaces the hard drive with flash memory: silent, no moving parts
Step-by-step guide iPod Mini 1st/2nd Gen hard drive (Microdrive) replacement (13 steps)
-
Next most likely
Loose or damaged hard drive cable
A loose or damaged hard drive cable can make the drive click, drop out or show the sad iPod face. Unless the problem started after a repair, the cable itself is rarely the fault on the Mini: if the microdrive isn't to blame, the logic board is just as likely as the cable.
Free check first Push the cable back in first; replace it only if that does not help.
Hard Drive Cable
For the iPod Mini 1st Gen
Hard Drive Ribbon Cable
For the iPod Mini 2nd Gen
iPod 3rd GeniPod 3rd Gen
Most likely: Failing hard driveNext: Loose or damaged hard drive cable
-
Most likely
Failing hard drive
Repeated clicking (the click of death: click, click, whir, or grinding) or the sad iPod face usually mean the hard drive is failing. A failed drive is the ideal time for a flash upgrade: flash storage has no heads, platters or motor, so the clicking, stalling and seizing that end an old hard drive can't happen. If your old drive still reads, add our music transfer ($149) and we copy everything on it onto the new flash storage.
Replacement Hard Drive
10GB · 15GB · 20GB · 30GB · 40GB
Flash Mod Service (installed by iMods)
Replaces the hard drive with flash memory: silent, no moving parts
Step-by-step guide iPod 3rd Gen hard drive replacement (14 steps)
-
Next most likely
Loose or damaged hard drive cable
A loose or damaged hard drive cable can make the drive click, drop out or show the sad iPod face. Unless the problem started after a repair, the cable itself is rarely the fault on the 3rd Gen: if the hard drive isn't to blame, the logic board is just as likely as the cable.
Free check first Push the cable back in first; replace it only if that does not help.
Hard Drive IDE Ribbon Cable
Frozen on ok to disconnect
Also searched as frozen on do not disconnect · ok to disconnect frozen · frozen do not disconnect · do not disconnect frozen
"OK to disconnect" means you can unplug it. If it stays stuck on "Do not disconnect" even after you eject it, unplug it and reset it, it is likely a hard drive problem: we recommend the free diagnostic first. While it shows "Do not disconnect", hold it up to your ear: unusual clicking patterns are a strong sign of a failing hard drive. On the 4th Gen and Photo, check the hard drive cable first, then the drive: our Hard Drive Repair Service is probably the best first option. On the other models, a drive failure is the ideal time for a flash upgrade.
Free checks first
- If it says "Do not disconnect", eject it first: the eject button in iTunes, or File > Eject in Finder. If the computer no longer shows the iPod but the message stays, you can unplug it.
- Reset it: press and hold Menu and the center (Select) button for 8 seconds, or until the Apple logo appears. If that fails, put the iPod on a table and press the center button without touching the wheel.
- Reset the 3rd Gen: hold Menu and Play/Pause until the Apple logo appears.
- Hold the iPod up to your ear: unusual clicking patterns are a strong sign that the hard drive is failing.
- Check the hard drive's health in Diagnostic Mode: on a healthy drive the reallocated sectors (reallocs) and pending sectors read zero or close to it. A high number, or numbers that rise each time you check, mean the drive is failing; pending sectors are the sharper warning.
iPod Classic 6th and 7th GeniPod Classic 6th GeniPod Classic 7th Gen
Most likely: Failing hard driveNext: Loose or damaged hard drive cable
-
Most likely
Failing hard drive
Repeated clicking (the click of death: click, click, whir, or grinding) or the red X usually mean the hard drive is failing. A failed drive is the ideal time for a flash upgrade: flash storage has no heads, platters or motor, so the clicking, stalling and seizing that end an old hard drive can't happen. If your old drive still reads, add our music transfer ($149) and we copy everything on it onto the new flash storage.
Replacement Hard Drive
For the iPod Classic 6th Gen
80GB · 120GB · 160GB
128GB Flash Mod Service (installed by iMods)
For the iPod Classic 6th Gen
Replaces the hard drive with flash memory: silent, no moving parts
Replacement Hard Drive 160GB (Late 2009)
For the iPod Classic 7th Gen
Flash Mod Service (installed by iMods)
For the iPod Classic 7th Gen
Replaces the hard drive with flash memory: silent, no moving parts
Step-by-step guide iPod Classic 6th/7th Gen hard drive replacement (11 steps)
-
Next most likely
Loose or damaged hard drive cable
A loose or damaged hard drive cable can make the drive click, drop out or show the red X. Unless the problem started after a repair, the cable itself is rarely the fault on the 6th and 7th Gen: if the hard drive isn't to blame, the logic board is just as likely as the cable.
Free check first Push the cable back in first; replace it only if that does not help.
Hard Drive Cable
For the iPod Classic 6th Gen
Thin · Thick
Hard Drive ZIF Ribbon Cable
For the iPod Classic 7th Gen
iPod Video 5th GeniPod Video 5th Gen
Most likely: Failing hard driveNext: Loose or damaged hard drive cable
-
Most likely
Failing hard drive
Repeated clicking (the click of death: click, click, whir, or grinding) or the sad iPod face usually mean the hard drive is failing. A failed drive is the ideal time for a flash upgrade: flash storage has no heads, platters or motor, so the clicking, stalling and seizing that end an old hard drive can't happen. If your old drive still reads, add our music transfer ($149) and we copy everything on it onto the new flash storage.
Flash Mod Service (installed by iMods)
Replaces the hard drive with flash memory: silent, no moving parts
Step-by-step guide iPod Video 5th Gen hard drive replacement (14 steps)
-
Next most likely
Loose or damaged hard drive cable
A loose or damaged hard drive cable can make the drive click, drop out or show the sad iPod face. Unless the problem started after a repair, the cable itself is rarely the fault on the iPod Video: if the hard drive isn't to blame, the logic board is just as likely as the cable.
Free check first Push the cable back in first; replace it only if that does not help.
iPod 4th Gen and iPod PhotoiPod 4th GeniPod Photo
Most likely: Loose or damaged hard drive cableNext: Failing hard drive
-
Most likely
Loose or damaged hard drive cable
On the 4th Gen and Photo, an iPod that seems too weak to spin up its hard drive often has a hard drive cable problem. A loose or damaged hard drive cable can make the drive click, drop out or show the sad iPod face. A cable fault sounds like click, whir; a failing drive sounds more like click, click, whir.
Free check first Clean the hard drive cable's contacts with 99% isopropyl alcohol (IPA) and re-seat it first; if that fails, it's likely a bad hard drive (our Hard Drive Repair Service is probably the best first option).
Hard Drive IDE Ribbon Cable
For the iPod Photo
-
Next most likely
Failing hard drive
Repeated clicking (the click of death: click, click, whir, or grinding) or the sad iPod face usually mean the hard drive is failing. Flash storage is the silent alternative to a new drive. On the 4th Gen and Photo we can often fix the hard drive without replacing it, and in most cases all songs are saved.
Hard Drive Repair Service
For the iPod 4th Gen
Mail it in: we repair your drive, and in most cases your songs are saved
Hard Drive Repair Service
For the iPod Photo
Mail it in: we repair your drive, and in most cases your songs are saved
Replacement Hard Drive
For the iPod 4th Gen
20GB · 40GB
Flash Mod Service (installed by iMods)
For the iPod 4th Gen
Replaces the hard drive with flash memory: silent, no moving parts
Replacement Hard Drive
For the iPod Photo
20GB · 30GB · 40GB · 60GB
Flash Mod Service (installed by iMods)
For the iPod Photo
Replaces the hard drive with flash memory: silent, no moving parts
Step-by-step guide iPod 4th Gen and iPod Photo hard drive replacement (12 steps)
iPod Mini 1st and 2nd GeniPod Mini 1st GeniPod Mini 2nd Gen
Most likely: Failed microdrive (the Mini's hard drive)Next: Loose or damaged hard drive cable
-
Most likely
Failed microdrive (the Mini's hard drive)
When the Mini's tiny hard drive (the microdrive) fails, it shows the sad iPod face or a folder icon, or makes clicking noises. Replace it with a used original microdrive, or upgrade to flash: a failed drive is the ideal time for it. Flash storage has no heads, platters or motor, so the clicking, stalling and seizing that end an old hard drive can't happen. If your old drive still reads, add our music transfer ($149) and we copy everything on it onto the new flash storage.
Replacement Microdrive (4GB)
For the iPod Mini 1st Gen
Flash Mod Service (installed by iMods)
For the iPod Mini 1st Gen
Replaces the hard drive with flash memory: silent, no moving parts
Replacement Microdrive
For the iPod Mini 2nd Gen
4GB · 6GB
Flash Mod Service (installed by iMods)
For the iPod Mini 2nd Gen
Replaces the hard drive with flash memory: silent, no moving parts
Step-by-step guide iPod Mini 1st/2nd Gen hard drive (Microdrive) replacement (13 steps)
-
Next most likely
Loose or damaged hard drive cable
A loose or damaged hard drive cable can make the drive click, drop out or show the sad iPod face. Unless the problem started after a repair, the cable itself is rarely the fault on the Mini: if the microdrive isn't to blame, the logic board is just as likely as the cable.
Free check first Push the cable back in first; replace it only if that does not help.
Hard Drive Cable
For the iPod Mini 1st Gen
Hard Drive Ribbon Cable
For the iPod Mini 2nd Gen
iPod 3rd GeniPod 3rd Gen
Most likely: Failing hard driveNext: Loose or damaged hard drive cable
-
Most likely
Failing hard drive
Repeated clicking (the click of death: click, click, whir, or grinding) or the sad iPod face usually mean the hard drive is failing. A failed drive is the ideal time for a flash upgrade: flash storage has no heads, platters or motor, so the clicking, stalling and seizing that end an old hard drive can't happen. If your old drive still reads, add our music transfer ($149) and we copy everything on it onto the new flash storage.
Replacement Hard Drive
10GB · 15GB · 20GB · 30GB · 40GB
Flash Mod Service (installed by iMods)
Replaces the hard drive with flash memory: silent, no moving parts
Step-by-step guide iPod 3rd Gen hard drive replacement (14 steps)
-
Next most likely
Loose or damaged hard drive cable
A loose or damaged hard drive cable can make the drive click, drop out or show the sad iPod face. Unless the problem started after a repair, the cable itself is rarely the fault on the 3rd Gen: if the hard drive isn't to blame, the logic board is just as likely as the cable.
Free check first Push the cable back in first; replace it only if that does not help.
Hard Drive IDE Ribbon Cable
Frozen on Apple logo
Also searched as frozen Apple logo · is frozen on the Apple logo
It freezes on the Apple logo.
See iPod stuck on the Apple logo
Free checks first
- Hold the iPod up to your ear: unusual clicking patterns are a strong sign that the hard drive is failing.
- Check the hard drive's health in Diagnostic Mode: on a healthy drive the reallocated sectors (reallocs) and pending sectors read zero or close to it. A high number, or numbers that rise each time you check, mean the drive is failing; pending sectors are the sharper warning.
iPod Classic 6th and 7th GeniPod Classic 6th GeniPod Classic 7th Gen
Most likely: Failing hard driveNext: Loose or damaged hard drive cable · 2 more causes
-
Most likely
Failing hard drive
Repeated clicking (the click of death: click, click, whir, or grinding) or the red X usually mean the hard drive is failing. A failed drive is the ideal time for a flash upgrade: flash storage has no heads, platters or motor, so the clicking, stalling and seizing that end an old hard drive can't happen. If your old drive still reads, add our music transfer ($149) and we copy everything on it onto the new flash storage.
Replacement Hard Drive
For the iPod Classic 6th Gen
80GB · 120GB · 160GB
128GB Flash Mod Service (installed by iMods)
For the iPod Classic 6th Gen
Replaces the hard drive with flash memory: silent, no moving parts
Replacement Hard Drive 160GB (Late 2009)
For the iPod Classic 7th Gen
Flash Mod Service (installed by iMods)
For the iPod Classic 7th Gen
Replaces the hard drive with flash memory: silent, no moving parts
Step-by-step guide iPod Classic 6th/7th Gen hard drive replacement (11 steps)
-
Next most likely
Loose or damaged hard drive cable
A loose or damaged hard drive cable can make the drive click, drop out or show the red X. Unless the problem started after a repair, the cable itself is rarely the fault on the 6th and 7th Gen: if the hard drive isn't to blame, the logic board is just as likely as the cable.
Free check first Push the cable back in first; replace it only if that does not help.
Hard Drive Cable
For the iPod Classic 6th Gen
Thin · Thick
Hard Drive ZIF Ribbon Cable
For the iPod Classic 7th Gen
-
Also possible
Battery too weak to spin up the hard drive
A worn battery cannot give the hard drive enough power to spin up, so the drive clicks and retries.
Free check first Connect it to a charger: that often tells whether the problem is the battery or something more serious.
Replacement Battery
For the iPod Classic 6th Gen
Thin · Thick
Replacement Battery (160GB)
For the iPod Classic 7th Gen
Step-by-step guide iPod Classic 6th/7th Gen battery replacement (13 steps)
-
Also possible
Damaged iPod software
The iPod's software is damaged, so it can't start properly or keeps freezing. Restoring it puts fresh software on it; a restore erases the songs on the iPod.
Free check first If it still shows up on a computer, copy your music off first, then restore it with iTunes (or Finder on a Mac with macOS Catalina or later). If the restore fails, or the problem comes back, the hard drive is the likely fault.
iPod Video 5th GeniPod Video 5th Gen
Most likely: Failing hard driveNext: Loose or damaged hard drive cable · 2 more causes
-
Most likely
Failing hard drive
Repeated clicking (the click of death: click, click, whir, or grinding) or the sad iPod face usually mean the hard drive is failing. A failed drive is the ideal time for a flash upgrade: flash storage has no heads, platters or motor, so the clicking, stalling and seizing that end an old hard drive can't happen. If your old drive still reads, add our music transfer ($149) and we copy everything on it onto the new flash storage.
Flash Mod Service (installed by iMods)
Replaces the hard drive with flash memory: silent, no moving parts
Step-by-step guide iPod Video 5th Gen hard drive replacement (14 steps)
-
Next most likely
Loose or damaged hard drive cable
A loose or damaged hard drive cable can make the drive click, drop out or show the sad iPod face. Unless the problem started after a repair, the cable itself is rarely the fault on the iPod Video: if the hard drive isn't to blame, the logic board is just as likely as the cable.
Free check first Push the cable back in first; replace it only if that does not help.
-
Also possible
Battery too weak to spin up the hard drive
A worn battery cannot give the hard drive enough power to spin up, so the drive clicks and retries.
Free check first Connect it to a charger: that often tells whether the problem is the battery or something more serious.
Step-by-step guide iPod Video 5th Gen battery replacement (10 steps)
-
Also possible
Damaged iPod software
The iPod's software is damaged, so it can't start properly or keeps freezing. Restoring it puts fresh software on it; a restore erases the songs on the iPod.
Free check first If it still shows up on a computer, copy your music off first, then restore it with iTunes (or Finder on a Mac with macOS Catalina or later). If the restore fails, or the problem comes back, the hard drive is the likely fault.
iPod 4th Gen and iPod PhotoiPod 4th GeniPod Photo
Most likely: Loose or damaged hard drive cableNext: Failing hard drive · 1 more cause
-
Most likely
Loose or damaged hard drive cable
On the 4th Gen and Photo, an iPod that seems too weak to spin up its hard drive often has a hard drive cable problem. A loose or damaged hard drive cable can make the drive click, drop out or show the sad iPod face. A cable fault sounds like click, whir; a failing drive sounds more like click, click, whir.
Free check first Clean the hard drive cable's contacts with 99% isopropyl alcohol (IPA) and re-seat it first; if that fails, it's likely a bad hard drive (our Hard Drive Repair Service is probably the best first option).
Hard Drive IDE Ribbon Cable
For the iPod Photo
-
Next most likely
Failing hard drive
Repeated clicking (the click of death: click, click, whir, or grinding) or the sad iPod face usually mean the hard drive is failing. Flash storage is the silent alternative to a new drive. On the 4th Gen and Photo we can often fix the hard drive without replacing it, and in most cases all songs are saved.
Hard Drive Repair Service
For the iPod 4th Gen
Mail it in: we repair your drive, and in most cases your songs are saved
Hard Drive Repair Service
For the iPod Photo
Mail it in: we repair your drive, and in most cases your songs are saved
Replacement Hard Drive
For the iPod 4th Gen
20GB · 40GB
Flash Mod Service (installed by iMods)
For the iPod 4th Gen
Replaces the hard drive with flash memory: silent, no moving parts
Replacement Hard Drive
For the iPod Photo
20GB · 30GB · 40GB · 60GB
Flash Mod Service (installed by iMods)
For the iPod Photo
Replaces the hard drive with flash memory: silent, no moving parts
Step-by-step guide iPod 4th Gen and iPod Photo hard drive replacement (12 steps)
-
Also possible
Damaged iPod software
The iPod's software is damaged, so it can't start properly or keeps freezing. Restoring it puts fresh software on it; a restore erases the songs on the iPod.
Free check first If it still shows up on a computer, copy your music off first, then restore it with iTunes (or Finder on a Mac with macOS Catalina or later). On the 4th Gen and iPod Photo the restore can stop at a picture of a plug: connect it to a wall charger to finish. Generic or incompatible wall chargers don't always give the iPod the right voltage: Apple's A1070 wall charger works with every model and is the ideal choice. If the restore fails, or the problem comes back, the hard drive cable, then the hard drive, is the likely fault (our Hard Drive Repair Service is probably the best first option).
iPod Mini 1st and 2nd GeniPod Mini 1st GeniPod Mini 2nd Gen
Most likely: Failed microdrive (the Mini's hard drive)Next: Loose or damaged hard drive cable · 2 more causes
-
Most likely
Failed microdrive (the Mini's hard drive)
When the Mini's tiny hard drive (the microdrive) fails, it shows the sad iPod face or a folder icon, or makes clicking noises. Replace it with a used original microdrive, or upgrade to flash: a failed drive is the ideal time for it. Flash storage has no heads, platters or motor, so the clicking, stalling and seizing that end an old hard drive can't happen. If your old drive still reads, add our music transfer ($149) and we copy everything on it onto the new flash storage.
Replacement Microdrive (4GB)
For the iPod Mini 1st Gen
Flash Mod Service (installed by iMods)
For the iPod Mini 1st Gen
Replaces the hard drive with flash memory: silent, no moving parts
Replacement Microdrive
For the iPod Mini 2nd Gen
4GB · 6GB
Flash Mod Service (installed by iMods)
For the iPod Mini 2nd Gen
Replaces the hard drive with flash memory: silent, no moving parts
Step-by-step guide iPod Mini 1st/2nd Gen hard drive (Microdrive) replacement (13 steps)
-
Next most likely
Loose or damaged hard drive cable
A loose or damaged hard drive cable can make the drive click, drop out or show the sad iPod face. Unless the problem started after a repair, the cable itself is rarely the fault on the Mini: if the microdrive isn't to blame, the logic board is just as likely as the cable.
Free check first Push the cable back in first; replace it only if that does not help.
Hard Drive Cable
For the iPod Mini 1st Gen
Hard Drive Ribbon Cable
For the iPod Mini 2nd Gen
-
Also possible
Battery too weak to spin up the hard drive
A worn battery cannot give the hard drive enough power to spin up, so the drive clicks and retries.
Free check first Connect it to a charger: that often tells whether the problem is the battery or something more serious.
Replacement Battery
For the iPod Mini 1st Gen
Replacement Battery
For the iPod Mini 2nd Gen
Step-by-step guide iPod Mini 1st/2nd Gen battery replacement (12 steps)
-
Also possible
Damaged iPod software
The iPod's software is damaged, so it can't start properly or keeps freezing. Restoring it puts fresh software on it; a restore erases the songs on the iPod.
Free check first If it still shows up on a computer, copy your music off first, then restore it with iTunes (or Finder on a Mac with macOS Catalina or later). On the Mini 1st Gen the restore can stop at a picture of a plug: connect it to a wall charger to finish. Generic or incompatible wall chargers don't always give the iPod the right voltage: Apple's A1070 wall charger works with every model and is the ideal choice. If the restore fails, or the problem comes back, the hard drive (Mini: microdrive) is the likely fault.
iPod 3rd GeniPod 3rd Gen
Most likely: Failing hard driveNext: Loose or damaged hard drive cable · 2 more causes
-
Most likely
Failing hard drive
Repeated clicking (the click of death: click, click, whir, or grinding) or the sad iPod face usually mean the hard drive is failing. A failed drive is the ideal time for a flash upgrade: flash storage has no heads, platters or motor, so the clicking, stalling and seizing that end an old hard drive can't happen. If your old drive still reads, add our music transfer ($149) and we copy everything on it onto the new flash storage.
Replacement Hard Drive
10GB · 15GB · 20GB · 30GB · 40GB
Flash Mod Service (installed by iMods)
Replaces the hard drive with flash memory: silent, no moving parts
Step-by-step guide iPod 3rd Gen hard drive replacement (14 steps)
-
Next most likely
Loose or damaged hard drive cable
A loose or damaged hard drive cable can make the drive click, drop out or show the sad iPod face. Unless the problem started after a repair, the cable itself is rarely the fault on the 3rd Gen: if the hard drive isn't to blame, the logic board is just as likely as the cable.
Free check first Push the cable back in first; replace it only if that does not help.
Hard Drive IDE Ribbon Cable
-
Also possible
Battery too weak to spin up the hard drive
A worn battery cannot give the hard drive enough power to spin up, so the drive clicks and retries.
Free check first Connect it to a charger: that often tells whether the problem is the battery or something more serious.
Replacement Battery (All Capacities)
Step-by-step guide iPod 3rd Gen battery replacement (14 steps)
-
Also possible
Damaged iPod software
The iPod's software is damaged, so it can't start properly or keeps freezing. Restoring it puts fresh software on it; a restore erases the songs on the iPod.
Free check first If it still shows up on a computer, copy your music off first, then restore it with iTunes (or Finder on a Mac with macOS Catalina or later). On the 3rd Gen the restore can stop at a picture of a plug: connect it to its FireWire wall charger to finish. Generic or incompatible wall chargers don't always give the iPod the right voltage: Apple's A1070 wall charger works with every model and is the ideal choice. If the restore fails, or the problem comes back, the hard drive is the likely fault.
Stuck on language screen
The language screen is what the iPod shows the first time it starts, after a restore, after a forced restart (a reset) or when the battery has run flat. If it stays there, it is most likely on Hold: the Hold switch is on, or it stays on Hold because of the headphone jack cable or a damaged logic board where that cable plugs in.
Free checks first
- Put the Hold switch firmly in the unlocked position. A locked iPod ignores every button.
- Using an iPod Remote? Its own Hold switch must be off too: Apple says the iPod's and the remote's Hold switches work separately.
- A lock icon at the top of the screen means the Hold switch is on: slide it to the unlocked position.
- Reset it: press and hold Menu and the center (Select) button for 8 seconds, or until the Apple logo appears. If that fails, put the iPod on a table and press the center button without touching the wheel.
- Reset the 3rd Gen: hold Menu and Play/Pause until the Apple logo appears.
iPod Classic 6th and 7th GeniPod Classic 6th GeniPod Classic 7th Gen
Most likely: Broken Hold switchNext: Logic board (headphone jack connector)
-
Most likely
Broken Hold switch
The Hold switch is part of the headphone jack assembly. If it is broken, stuck, or leaves the iPod locked with the switch off, a new headphone jack assembly fixes it.
Replacement Headphone Jack
For the iPod Classic 6th Gen
Thin · Thick
Replacement Headphone Jack
For the iPod Classic 7th Gen
Step-by-step guide iPod Classic 6th/7th Gen headphone jack and Hold switch replacement (13 steps)
-
Next most likely
Logic board (headphone jack connector)
If the Hold switch and the headphone jack cable are all right and the iPod still stays on Hold, the logic board may be damaged where the headphone jack cable plugs in. We fix it by replacing the logic board.
Replacement Logic Board
For the iPod Classic 6th Gen
2007 · Late 2008
Replacement Logic Board
For the iPod Classic 7th Gen
iPod Video 5th GeniPod Video 5th Gen
Most likely: Broken Hold switchNext: Logic board (headphone jack connector)
-
Most likely
Broken Hold switch
The Hold switch is part of the headphone jack assembly. If it is broken, stuck, or leaves the iPod locked with the switch off, a new headphone jack assembly fixes it.
Step-by-step guide iPod Video 5th Gen headphone jack and Hold switch replacement (13 steps)
-
Next most likely
Logic board (headphone jack connector)
If the Hold switch and the headphone jack cable are all right and the iPod still stays on Hold, the logic board may be damaged where the headphone jack cable plugs in. We fix it by replacing the logic board.
Replacement Logic Board
30GB 5G · 30GB 5.5G Enhanced · 60GB 5G · 80GB 5.5G Enhanced
iPod 4th Gen and iPod PhotoiPod 4th GeniPod Photo
Most likely: Headphone jack cable keeping it lockedNext: Broken Hold switch · 1 more cause
-
Most likely
Headphone jack cable keeping it locked
A faulty headphone jack cable can keep the iPod locked, so the click wheel cannot wake it. The cable doesn't have to be damaged: it may just not be snapped fully into the logic board or pushed fully into the headphone jack board. It easily comes out when the case is first opened, for example in a battery swap.
Free check first Put the Hold switch firmly in the unlocked position and look for a lock symbol at the top of the screen. If it still shows, the headphone jack cable is likely loose or faulty: open the iPod and push it fully back into the logic board and the headphone jack board before buying a new cable.
Headphone Jack Flex Cable
For the iPod 4th Gen
Headphone Jack Flex Cable
For the iPod Photo
Step-by-step guide iPod 4th Gen and iPod Photo headphone jack replacement (11 steps)
-
Next most likely
Broken Hold switch
The Hold switch is part of the headphone jack assembly. If it is broken, stuck, or leaves the iPod locked with the switch off, a new headphone jack assembly fixes it. On the 4th Gen and iPod Photo the Hold switch sits on its own board (the headphone jack board), with its slider on a plastic bracket.
Replacement Headphone Jack
For the iPod 4th Gen
Thin · Thick
Replacement Headphone Jack
For the iPod Photo
Thin · Thick
Step-by-step guide iPod 4th Gen and iPod Photo headphone jack replacement (11 steps)
-
Also possible
Logic board (headphone jack connector)
If the Hold switch and the headphone jack cable are all right and the iPod still stays on Hold, the logic board may be damaged where the headphone jack cable plugs in. We fix it by replacing the logic board.
Replacement Logic Board
For the iPod 4th Gen
Replacement Logic Board
For the iPod Photo
Late 2004 to early 2005 · Mid-2005
iPod Mini 1st and 2nd GeniPod Mini 1st GeniPod Mini 2nd Gen
Most likely: Broken Hold switchNext: Logic board (headphone jack connector)
-
Most likely
Broken Hold switch
On the Mini the Hold switch sits on the small headphone jack board. If it is broken, stuck, or leaves the iPod locked with the switch off, a new headphone jack board fixes it.
Headphone Jack / Hold Switch Assembly
For the iPod Mini 1st Gen
Headphone Jack / Hold Switch Assembly
For the iPod Mini 2nd Gen
Step-by-step guide iPod Mini 1st/2nd Gen headphone jack and Hold switch replacement (12 steps)
-
Next most likely
Logic board (headphone jack connector)
If the Hold switch and the headphone jack board are all right and the iPod still stays on Hold, the logic board may be damaged where the jack board plugs in, or that connector may have torn off the board. We fix it by replacing the logic board.
Replacement Logic Board
For the iPod Mini 1st Gen
Replacement Logic Board
For the iPod Mini 2nd Gen
iPod 3rd GeniPod 3rd Gen
Most likely: Broken Hold switchNext: Logic board (headphone jack connector)
-
Most likely
Broken Hold switch
On the 3rd Gen the Hold slider sits on the headphone jack assembly and moves a small switch on the logic board. If the slider is broken or stuck, or leaves the iPod locked with the switch off, a new headphone jack assembly fixes it. After the iPod has been opened, the slider and the switch on the board must line up, or Hold stops working.
Step-by-step guide iPod 3rd Gen headphone jack and Hold switch replacement (12 steps)
-
Next most likely
Logic board (headphone jack connector)
If the Hold switch and the headphone jack cable are all right and the iPod still stays on Hold, the logic board may be damaged where the headphone jack cable plugs in. We fix it by replacing the logic board.
Replacement Logic Board
Started after a repair or part swap
It started freezing after the iPod was opened.
iPod Classic 6th and 7th GeniPod Classic 6th GeniPod Classic 7th Gen
Most likely: Hard drive cable not fully in, or a latch left openNext: Loose or damaged hard drive cable · 1 more cause
-
Most likely
Hard drive cable not fully in, or a latch left open
After the iPod has been opened, a hard drive cable that isn't pushed fully in, or a drive or cable latch left open, stops the drive from working.
Free check first Open it again, push the hard drive cable fully in and close every latch.
-
Next most likely
Loose or damaged hard drive cable
A loose or damaged hard drive cable can make the drive click, drop out or show the red X. Unless the problem started after a repair, the cable itself is rarely the fault on the 6th and 7th Gen: if the hard drive isn't to blame, the logic board is just as likely as the cable.
Free check first Push the cable back in first; replace it only if that does not help.
Hard Drive Cable
For the iPod Classic 6th Gen
Thin · Thick
Hard Drive ZIF Ribbon Cable
For the iPod Classic 7th Gen
-
Also possible
A connector not seated after the repair
After a battery or part swap, a connector that is not fully seated can leave the iPod dead or half-working. We can also look at it: the free diagnostic finds the issue and whether it can be fixed without new parts.
Free check first Open it again and push every connector you touched fully back in.
iPod Video 5th GeniPod Video 5th Gen
Most likely: Hard drive cable not fully in, or a latch left openNext: Loose or damaged hard drive cable · 1 more cause
-
Most likely
Hard drive cable not fully in, or a latch left open
After the iPod has been opened, a hard drive cable that isn't pushed fully in, or a drive or cable latch left open, stops the drive from working.
Free check first Open it again, push the hard drive cable fully in and close every latch.
-
Next most likely
Loose or damaged hard drive cable
A loose or damaged hard drive cable can make the drive click, drop out or show the sad iPod face. Unless the problem started after a repair, the cable itself is rarely the fault on the iPod Video: if the hard drive isn't to blame, the logic board is just as likely as the cable.
Free check first Push the cable back in first; replace it only if that does not help.
-
Also possible
A connector not seated after the repair
After a battery or part swap, a connector that is not fully seated can leave the iPod dead or half-working. We can also look at it: the free diagnostic finds the issue and whether it can be fixed without new parts.
Free check first Open it again and push every connector you touched fully back in.
iPod 4th Gen and iPod PhotoiPod 4th GeniPod Photo
Most likely: Hard drive cable not fully in, or a latch left openNext: Loose or damaged hard drive cable · 1 more cause
-
Most likely
Hard drive cable not fully in, or a latch left open
After the iPod has been opened, a hard drive cable that isn't pushed fully in, or a drive or cable latch left open, stops the drive from working.
Free check first Open it again, push the hard drive cable fully in and close every latch.
-
Next most likely
Loose or damaged hard drive cable
On the 4th Gen and Photo, an iPod that seems too weak to spin up its hard drive often has a hard drive cable problem. A loose or damaged hard drive cable can make the drive click, drop out or show the sad iPod face. A cable fault sounds like click, whir; a failing drive sounds more like click, click, whir.
Free check first Clean the hard drive cable's contacts with 99% isopropyl alcohol (IPA) and re-seat it first; if that fails, it's likely a bad hard drive (our Hard Drive Repair Service is probably the best first option).
Hard Drive IDE Ribbon Cable
For the iPod Photo
-
Also possible
A connector not seated after the repair
After a battery or part swap, a connector that is not fully seated can leave the iPod dead or half-working. We can also look at it: the free diagnostic finds the issue and whether it can be fixed without new parts.
Free check first Open it again and push every connector you touched fully back in.
iPod Mini 1st and 2nd GeniPod Mini 1st GeniPod Mini 2nd Gen
Most likely: Hard drive cable not fully in, or a latch left openNext: Loose or damaged hard drive cable · 1 more cause
-
Most likely
Hard drive cable not fully in, or a latch left open
After the iPod has been opened, a hard drive cable that isn't pushed fully in, or a drive or cable latch left open, stops the drive from working.
Free check first Open it again, push the hard drive cable fully in and close every latch.
-
Next most likely
Loose or damaged hard drive cable
A loose or damaged hard drive cable can make the drive click, drop out or show the sad iPod face. Unless the problem started after a repair, the cable itself is rarely the fault on the Mini: if the microdrive isn't to blame, the logic board is just as likely as the cable.
Free check first Push the cable back in first; replace it only if that does not help.
Hard Drive Cable
For the iPod Mini 1st Gen
Hard Drive Ribbon Cable
For the iPod Mini 2nd Gen
-
Also possible
A connector not seated after the repair
After a battery or part swap, a connector that is not fully seated can leave the iPod dead or half-working. We can also look at it: the free diagnostic finds the issue and whether it can be fixed without new parts.
Free check first Open it again and push every connector you touched fully back in.
iPod 3rd GeniPod 3rd Gen
Most likely: Hard drive cable not fully in, or a latch left openNext: Loose or damaged hard drive cable · 1 more cause
-
Most likely
Hard drive cable not fully in, or a latch left open
After the iPod has been opened, a hard drive cable that isn't pushed fully in, or a drive or cable latch left open, stops the drive from working.
Free check first Open it again, push the hard drive cable fully in and close every latch.
-
Next most likely
Loose or damaged hard drive cable
A loose or damaged hard drive cable can make the drive click, drop out or show the sad iPod face. Unless the problem started after a repair, the cable itself is rarely the fault on the 3rd Gen: if the hard drive isn't to blame, the logic board is just as likely as the cable.
Free check first Push the cable back in first; replace it only if that does not help.
Hard Drive IDE Ribbon Cable
-
Also possible
A connector not seated after the repair
After a battery or part swap, a connector that is not fully seated can leave the iPod dead or half-working. We can also look at it: the free diagnostic finds the issue and whether it can be fixed without new parts.
Free check first Open it again and push every connector you touched fully back in.
Not sure — free diagnostic
Mail us your iPod and we test it and send you a free repair quote. If you don't like the price, we ship it back at our expense.
Free
Which iPod do you have?
The page shows the causes for the iPod you pick.
Not sure which one? Identify your iPod