Startup & storage
iPod stuck on Apple logo
Stuck on the Apple logo, flashing it, or restarting over and over? Pick what happens and your model to see the likely causes and what each fix costs.
What exactly happens?
- Stuck on Apple logoAlso searched as stuck on Apple screen · is stuck on Apple logo · frozen on Apple logo · only shows Apple logo · stays on Apple logo · Apple logo · just shows Apple logo · only shows the Apple logo · won't turn on past Apple logo · won't go past Apple logo · shows Apple logo only · stuck on Apple logo screen · showing Apple icon only · is stuck on the Apple screen · just shows the Apple logo · showing Apple logo only · stuck on Apple logo after restore · won't boot past Apple logo · keeps showing Apple logo · iPod stuck on Apple logo when booting · Apple symbol stuck on screen · showing Apple logo
- Keeps restartingAlso searched as boot loop · Apple logo flashes on and off · flashing Apple logo · keeps restarting Apple logo · keeps flashing Apple logo · reboot loop · stuck in boot loop · keeps resetting · stuck in reboot loop · keeps rebooting · flashing Apple logo when plugged in · keeps restarting when plugged in · flashing the Apple logo · screen flashing Apple logo · bootloop · bootlooping · stuck on bootloop
- Stuck on Apple logo then turns offAlso searched as Apple logo appears then disappears · shows Apple logo then shuts off · shows Apple logo then turns off
- Started after a repair or part swap
- Not sure — free diagnostic
Which iPod do you have?
Most common causes, by model
Charge it and reset it first, then restore it. An iPod that still stops at the Apple logo or keeps restarting most often has a failing hard drive, often with the sad iPod face (on the 6th and 7th Gen, the red X). On the 4th Gen and Photo, check the hard drive cable first, then the drive: our Hard Drive Repair Service is probably the best first option. On the other models, a drive failure is the ideal time for a flash upgrade.
Free checks first
- If it still shows up on a computer, copy your music off before anything else (copy the whole iPod_Control folder to keep more than the songs); if it clicks or drops off the computer while copying, stop and get it diagnosed.
- Leave it on the charger for at least 30 minutes: a very empty battery has to charge before the iPod can start.
- On the 3rd Gen, charge from a FireWire charger or a 6-pin FireWire port on a computer that is on and awake: its USB cable syncs but never charges it.
- Reset it: press and hold Menu and the center (Select) button for 8 seconds, or until the Apple logo appears. If that fails, put the iPod on a table and press the center button without touching the wheel.
- Reset the 3rd Gen: hold Menu and Play/Pause until the Apple logo appears.
- Click wheel iPods (4th Gen, Photo, Video, Classic and Mini): if the computer does not see it, use Disk Mode: put the Hold switch firmly in the unlocked position, hold Menu and Center until the Apple logo appears, let go, then hold Center and Play/Pause until the Disk Mode screen appears.
- On the 6th and 7th Gen, if the restore keeps failing or the computer doesn't see it at all, try DFU mode: connect it, hold Menu and Center until it restarts, and keep holding until it restarts again; the screen stays blank, and in some cases the computer then recognizes it and offers a restore.
- iPod 3rd Gen (four buttons above the wheel): if the computer does not see it, use Disk Mode: put the Hold switch firmly in the unlocked position, hold Menu and Play/Pause until the Apple logo appears, let go, then hold Previous and Next until the Disk Mode screen appears.
- Restore it: use Finder on a Mac with macOS Catalina or later, or iTunes on an older Mac or a PC. Connect the iPod straight to the computer, find it, then choose Restore iPod. A restore erases all songs on the iPod.
- Can't get it into Disk Mode at all? On the 3rd Gen, 4th Gen, iPod Photo, Mini and iPod Video, Apple says an iPod that only shows the Apple logo and won't go into Disk Mode may need a repair.
- On the 3rd Gen, 4th Gen, iPod Photo and Mini 1st Gen the restore can stop at a picture of a plug: connect it to the wall charger (3rd Gen: its FireWire wall charger) to finish. Generic or incompatible wall chargers don't always give the iPod the right voltage: Apple's A1070 wall charger works with every model and is the ideal choice.
- Hold the iPod up to your ear: unusual clicking patterns are a strong sign that the hard drive is failing.
- Check the hard drive's health in Diagnostic Mode: on a healthy drive the reallocated sectors (reallocs) and pending sectors read zero or close to it. A high number, or numbers that rise each time you check, mean the drive is failing; pending sectors are the sharper warning.
iPod Classic (A1238) stuck on the Apple logoiPod Classic 6th Gen (A1238) stuck on the Apple logoiPod Classic 7th Gen (A1238) stuck on the Apple logo
-
Most likely
Failing hard drive
Repeated clicking (the click of death: click, click, whir, or grinding) or the red X usually mean the hard drive is failing. A failed drive is the ideal time for a flash upgrade: flash storage has no heads, platters or motor, so the clicking, stalling and seizing that end an old hard drive can't happen. If your old drive still reads, add our music transfer ($129) and we copy everything on it onto the new flash storage.
Flash Mod Service (installed by iMods)
Replaces the hard drive with flash memory: silent, no moving parts
Replacement Hard Drive 160GB (Late 2009)
Flash Mod Service (installed by iMods)
Replaces the hard drive with flash memory: silent, no moving parts
-
Next most likely
Loose or damaged hard drive cable
A loose or damaged hard drive cable can make the drive click, drop out or show the red X. Unless the problem started after a repair, the cable itself is rarely the fault on the 6th and 7th Gen: if the hard drive isn't to blame, the logic board is just as likely as the cable.
Free check first Push the cable back in first; replace it only if that does not help.
Hard Drive ZIF Ribbon Cable
-
Also possible
Battery too weak to spin up the hard drive
A worn battery cannot give the hard drive enough power to spin up, so the drive clicks and retries.
Free check first Connect it to a charger: that often tells whether the problem is the battery or something more serious.
Replacement Battery (160GB)
-
Also possible
Damaged iPod software
The iPod's software is damaged, so it can't start properly or keeps freezing. Restoring it puts fresh software on it; a restore erases the songs on the iPod.
Free check first If it still shows up on a computer, copy your music off first, then restore it with iTunes (or Finder on a Mac with macOS Catalina or later). If the restore fails, or the problem comes back, the hard drive is the likely fault.
More causes on this page, depending on what happens
- Hard drive cable not fully in, or a latch left openStarted after a repair or part swap
- A connector not seated after the repairStarted after a repair or part swap
iPod Video (A1136) stuck on the Apple logoiPod Video 5th Gen (A1136) stuck on the Apple logo
-
Most likely
Failing hard drive
Repeated clicking (the click of death: click, click, whir, or grinding) or the sad iPod face usually mean the hard drive is failing. A failed drive is the ideal time for a flash upgrade: flash storage has no heads, platters or motor, so the clicking, stalling and seizing that end an old hard drive can't happen. If your old drive still reads, add our music transfer ($129) and we copy everything on it onto the new flash storage.
Flash Mod Service (installed by iMods)
Replaces the hard drive with flash memory: silent, no moving parts
-
Next most likely
Loose or damaged hard drive cable
A loose or damaged hard drive cable can make the drive click, drop out or show the sad iPod face. Unless the problem started after a repair, the cable itself is rarely the fault on the iPod Video: if the hard drive isn't to blame, the logic board is just as likely as the cable.
Free check first Push the cable back in first; replace it only if that does not help.
-
Also possible
Battery too weak to spin up the hard drive
A worn battery cannot give the hard drive enough power to spin up, so the drive clicks and retries.
Free check first Connect it to a charger: that often tells whether the problem is the battery or something more serious.
-
Also possible
Damaged iPod software
The iPod's software is damaged, so it can't start properly or keeps freezing. Restoring it puts fresh software on it; a restore erases the songs on the iPod.
Free check first If it still shows up on a computer, copy your music off first, then restore it with iTunes (or Finder on a Mac with macOS Catalina or later). If the restore fails, or the problem comes back, the hard drive is the likely fault.
More causes on this page, depending on what happens
- Hard drive cable not fully in, or a latch left openStarted after a repair or part swap
- A connector not seated after the repairStarted after a repair or part swap
iPod 4th Gen or iPod Photo (A1059 and A1099) stuck on the Apple logoiPod 4th Gen (A1059) stuck on the Apple logoiPod Photo (A1099) stuck on the Apple logo
-
Most likely
Loose or damaged hard drive cable
On the 4th Gen and Photo, an iPod that seems too weak to spin up its hard drive often has a hard drive cable problem. A loose or damaged hard drive cable can make the drive click, drop out or show the sad iPod face. A cable fault sounds like click, whir; a failing drive sounds more like click, click, whir.
Free check first Clean the hard drive cable's contacts with 99% isopropyl alcohol (IPA) and re-seat it first; if that fails, it's likely a bad hard drive (our Hard Drive Repair Service is probably the best first option).
Hard Drive IDE Ribbon Cable
Hard Drive IDE Ribbon Cable
-
Next most likely
Failing hard drive
Repeated clicking (the click of death: click, click, whir, or grinding) or the sad iPod face usually mean the hard drive is failing. Flash storage is the silent alternative to a new drive. On the 4th Gen and Photo we can often fix the hard drive without replacing it, and in most cases all songs are saved.
Hard Drive Repair Service
Mail it in: we repair your drive, and in most cases your songs are saved
Hard Drive Repair Service
Mail it in: we repair your drive, and in most cases your songs are saved
Flash Mod Service (installed by iMods)
Replaces the hard drive with flash memory: silent, no moving parts
Replacement Hard Drive
20GB · 30GB · 40GB · 60GB
Flash Mod Service (installed by iMods)
Replaces the hard drive with flash memory: silent, no moving parts
-
Also possible
Battery too weak to spin up the hard drive
A worn battery cannot give the hard drive enough power to spin up, so the drive clicks and retries. On the 4th Gen and Photo this is rarely the answer: far more often it is the hard drive cable. On the 4th Gen and Photo this is rarely the cause: the hard drive cable is far more often the fault.
Free check first Connect it to a charger: that often tells whether the problem is the battery or something more serious. If it still clicks and restarts on the charger, the battery is very unlikely to be the problem. If it still clicks and restarts on the charger, the battery is very unlikely to be the problem.
Replacement Battery (All Capacities)
Replacement Battery
-
Also possible
Damaged iPod software
The iPod's software is damaged, so it can't start properly or keeps freezing. Restoring it puts fresh software on it; a restore erases the songs on the iPod.
Free check first If it still shows up on a computer, copy your music off first, then restore it with iTunes (or Finder on a Mac with macOS Catalina or later). On the 4th Gen and iPod Photo the restore can stop at a picture of a plug: connect it to a wall charger to finish. Generic or incompatible wall chargers don't always give the iPod the right voltage: Apple's A1070 wall charger works with every model and is the ideal choice. If the restore fails, or the problem comes back, the hard drive cable, then the hard drive, is the likely fault (our Hard Drive Repair Service is probably the best first option).
More causes on this page, depending on what happens
- Hard drive cable not fully in, or a latch left openStarted after a repair or part swap
- A connector not seated after the repairStarted after a repair or part swap
iPod Mini (A1051) stuck on the Apple logoiPod Mini 1st Gen (A1051) stuck on the Apple logoiPod Mini 2nd Gen (A1051) stuck on the Apple logo
-
Most likely
Failed microdrive (the Mini's hard drive)
When the Mini's tiny hard drive (the microdrive) fails, it shows the sad iPod face or a folder icon, or makes clicking noises. Replace it with a used original microdrive, or upgrade to flash: a failed drive is the ideal time for it. Flash storage has no heads, platters or motor, so the clicking, stalling and seizing that end an old hard drive can't happen. If your old drive still reads, add our music transfer ($129) and we copy everything on it onto the new flash storage.
Replacement Microdrive (4GB)
Flash Mod Service (installed by iMods)
Replaces the hard drive with flash memory: silent, no moving parts
Flash Mod Service (installed by iMods)
Replaces the hard drive with flash memory: silent, no moving parts
-
Next most likely
Loose or damaged hard drive cable
A loose or damaged hard drive cable can make the drive click, drop out or show the sad iPod face. Unless the problem started after a repair, the cable itself is rarely the fault on the Mini: if the microdrive isn't to blame, the logic board is just as likely as the cable.
Free check first Push the cable back in first; replace it only if that does not help.
Hard Drive Cable
Hard Drive Ribbon Cable
-
Also possible
Battery too weak to spin up the hard drive
A worn battery cannot give the hard drive enough power to spin up, so the drive clicks and retries.
Free check first Connect it to a charger: that often tells whether the problem is the battery or something more serious.
Replacement Battery
Replacement Battery
-
Also possible
Damaged iPod software
The iPod's software is damaged, so it can't start properly or keeps freezing. Restoring it puts fresh software on it; a restore erases the songs on the iPod.
Free check first If it still shows up on a computer, copy your music off first, then restore it with iTunes (or Finder on a Mac with macOS Catalina or later). On the Mini 1st Gen the restore can stop at a picture of a plug: connect it to a wall charger to finish. Generic or incompatible wall chargers don't always give the iPod the right voltage: Apple's A1070 wall charger works with every model and is the ideal choice. If the restore fails, or the problem comes back, the hard drive (Mini: microdrive) is the likely fault.
More causes on this page, depending on what happens
- Hard drive cable not fully in, or a latch left openStarted after a repair or part swap
- A connector not seated after the repairStarted after a repair or part swap
iPod 3rd Gen (A1040) stuck on the Apple logoiPod 3rd Gen (A1040) stuck on the Apple logo
-
Most likely
Failing hard drive
Repeated clicking (the click of death: click, click, whir, or grinding) or the sad iPod face usually mean the hard drive is failing. A failed drive is the ideal time for a flash upgrade: flash storage has no heads, platters or motor, so the clicking, stalling and seizing that end an old hard drive can't happen. If your old drive still reads, add our music transfer ($129) and we copy everything on it onto the new flash storage.
Replacement Hard Drive
10GB · 15GB · 20GB · 30GB · 40GB
Flash Mod Service (installed by iMods)
Replaces the hard drive with flash memory: silent, no moving parts
-
Next most likely
Loose or damaged hard drive cable
A loose or damaged hard drive cable can make the drive click, drop out or show the sad iPod face. Unless the problem started after a repair, the cable itself is rarely the fault on the 3rd Gen: if the hard drive isn't to blame, the logic board is just as likely as the cable.
Free check first Push the cable back in first; replace it only if that does not help.
Hard Drive IDE Ribbon Cable
-
Also possible
Battery too weak to spin up the hard drive
A worn battery cannot give the hard drive enough power to spin up, so the drive clicks and retries.
Free check first Connect it to a charger: that often tells whether the problem is the battery or something more serious.
Replacement Battery (All Capacities)
-
Also possible
Damaged iPod software
The iPod's software is damaged, so it can't start properly or keeps freezing. Restoring it puts fresh software on it; a restore erases the songs on the iPod.
Free check first If it still shows up on a computer, copy your music off first, then restore it with iTunes (or Finder on a Mac with macOS Catalina or later). On the 3rd Gen the restore can stop at a picture of a plug: connect it to its FireWire wall charger to finish. Generic or incompatible wall chargers don't always give the iPod the right voltage: Apple's A1070 wall charger works with every model and is the ideal choice. If the restore fails, or the problem comes back, the hard drive is the likely fault.
More causes on this page, depending on what happens
- Hard drive cable not fully in, or a latch left openStarted after a repair or part swap
- A connector not seated after the repairStarted after a repair or part swap
Keeps restarting
Also searched as boot loop · Apple logo flashes on and off · flashing Apple logo · keeps restarting Apple logo · keeps flashing Apple logo · reboot loop · stuck in boot loop · keeps resetting · stuck in reboot loop · keeps rebooting · flashing Apple logo when plugged in · keeps restarting when plugged in · flashing the Apple logo · screen flashing Apple logo · bootloop · bootlooping · stuck on bootloop
It keeps restarting: the Apple logo flashes on and off.
Free checks first
- Put it on a wall charger (3rd Gen: its FireWire wall charger) and let it start: with a flat battery it can restart a couple of times before it starts up. If it starts up on the charger but keeps restarting when you unplug it, the battery is likely too weak to spin up the hard drive. If it keeps restarting even on the charger, the hard drive is the most likely fault (Mini: its microdrive; 4th Gen and Photo: the drive cable first, then the drive).
- On the 4th Gen and Photo a weak battery is rarely the cause, and very unlikely if it keeps restarting on the charger too: the hard drive cable is far more often the fault, then the hard drive.
- Flash-upgraded iPod that keeps restarting after a big sync? Its library may be too big for the iPod's memory: put it in Disk Mode and remove some songs.
- Hold the iPod up to your ear: unusual clicking patterns are a strong sign that the hard drive is failing.
- Check the hard drive's health in Diagnostic Mode: on a healthy drive the reallocated sectors (reallocs) and pending sectors read zero or close to it. A high number, or numbers that rise each time you check, mean the drive is failing; pending sectors are the sharper warning.
iPod Classic 6th and 7th GeniPod Classic 6th GeniPod Classic 7th Gen
-
Most likely
Failing hard drive
Repeated clicking (the click of death: click, click, whir, or grinding) or the red X usually mean the hard drive is failing. A failed drive is the ideal time for a flash upgrade: flash storage has no heads, platters or motor, so the clicking, stalling and seizing that end an old hard drive can't happen. If your old drive still reads, add our music transfer ($129) and we copy everything on it onto the new flash storage.
Flash Mod Service (installed by iMods)
Replaces the hard drive with flash memory: silent, no moving parts
Replacement Hard Drive 160GB (Late 2009)
Flash Mod Service (installed by iMods)
Replaces the hard drive with flash memory: silent, no moving parts
-
Next most likely
Loose or damaged hard drive cable
A loose or damaged hard drive cable can make the drive click, drop out or show the red X. Unless the problem started after a repair, the cable itself is rarely the fault on the 6th and 7th Gen: if the hard drive isn't to blame, the logic board is just as likely as the cable.
Free check first Push the cable back in first; replace it only if that does not help.
Hard Drive ZIF Ribbon Cable
-
Also possible
Battery too weak to spin up the hard drive
A worn battery cannot give the hard drive enough power to spin up, so the drive clicks and retries.
Free check first Connect it to a charger: that often tells whether the problem is the battery or something more serious.
Replacement Battery (160GB)
-
Also possible
Damaged iPod software
The iPod's software is damaged, so it can't start properly or keeps freezing. Restoring it puts fresh software on it; a restore erases the songs on the iPod.
Free check first If it still shows up on a computer, copy your music off first, then restore it with iTunes (or Finder on a Mac with macOS Catalina or later). If the restore fails, or the problem comes back, the hard drive is the likely fault.
iPod Video 5th GeniPod Video 5th Gen
-
Most likely
Failing hard drive
Repeated clicking (the click of death: click, click, whir, or grinding) or the sad iPod face usually mean the hard drive is failing. A failed drive is the ideal time for a flash upgrade: flash storage has no heads, platters or motor, so the clicking, stalling and seizing that end an old hard drive can't happen. If your old drive still reads, add our music transfer ($129) and we copy everything on it onto the new flash storage.
Flash Mod Service (installed by iMods)
Replaces the hard drive with flash memory: silent, no moving parts
-
Next most likely
Loose or damaged hard drive cable
A loose or damaged hard drive cable can make the drive click, drop out or show the sad iPod face. Unless the problem started after a repair, the cable itself is rarely the fault on the iPod Video: if the hard drive isn't to blame, the logic board is just as likely as the cable.
Free check first Push the cable back in first; replace it only if that does not help.
-
Also possible
Battery too weak to spin up the hard drive
A worn battery cannot give the hard drive enough power to spin up, so the drive clicks and retries.
Free check first Connect it to a charger: that often tells whether the problem is the battery or something more serious.
-
Also possible
Damaged iPod software
The iPod's software is damaged, so it can't start properly or keeps freezing. Restoring it puts fresh software on it; a restore erases the songs on the iPod.
Free check first If it still shows up on a computer, copy your music off first, then restore it with iTunes (or Finder on a Mac with macOS Catalina or later). If the restore fails, or the problem comes back, the hard drive is the likely fault.
iPod 4th Gen and iPod PhotoiPod 4th GeniPod Photo
-
Most likely
Loose or damaged hard drive cable
On the 4th Gen and Photo, an iPod that seems too weak to spin up its hard drive often has a hard drive cable problem. A loose or damaged hard drive cable can make the drive click, drop out or show the sad iPod face. A cable fault sounds like click, whir; a failing drive sounds more like click, click, whir.
Free check first Clean the hard drive cable's contacts with 99% isopropyl alcohol (IPA) and re-seat it first; if that fails, it's likely a bad hard drive (our Hard Drive Repair Service is probably the best first option).
Hard Drive IDE Ribbon Cable
Hard Drive IDE Ribbon Cable
-
Next most likely
Failing hard drive
Repeated clicking (the click of death: click, click, whir, or grinding) or the sad iPod face usually mean the hard drive is failing. Flash storage is the silent alternative to a new drive. On the 4th Gen and Photo we can often fix the hard drive without replacing it, and in most cases all songs are saved.
Hard Drive Repair Service
Mail it in: we repair your drive, and in most cases your songs are saved
Hard Drive Repair Service
Mail it in: we repair your drive, and in most cases your songs are saved
Flash Mod Service (installed by iMods)
Replaces the hard drive with flash memory: silent, no moving parts
Replacement Hard Drive
20GB · 30GB · 40GB · 60GB
Flash Mod Service (installed by iMods)
Replaces the hard drive with flash memory: silent, no moving parts
-
Also possible
Battery too weak to spin up the hard drive
A worn battery cannot give the hard drive enough power to spin up, so the drive clicks and retries. On the 4th Gen and Photo this is rarely the answer: far more often it is the hard drive cable. On the 4th Gen and Photo this is rarely the cause: the hard drive cable is far more often the fault.
Free check first Connect it to a charger: that often tells whether the problem is the battery or something more serious. If it still clicks and restarts on the charger, the battery is very unlikely to be the problem. If it still clicks and restarts on the charger, the battery is very unlikely to be the problem.
Replacement Battery (All Capacities)
Replacement Battery
-
Also possible
Damaged iPod software
The iPod's software is damaged, so it can't start properly or keeps freezing. Restoring it puts fresh software on it; a restore erases the songs on the iPod.
Free check first If it still shows up on a computer, copy your music off first, then restore it with iTunes (or Finder on a Mac with macOS Catalina or later). On the 4th Gen and iPod Photo the restore can stop at a picture of a plug: connect it to a wall charger to finish. Generic or incompatible wall chargers don't always give the iPod the right voltage: Apple's A1070 wall charger works with every model and is the ideal choice. If the restore fails, or the problem comes back, the hard drive cable, then the hard drive, is the likely fault (our Hard Drive Repair Service is probably the best first option).
iPod Mini 1st and 2nd GeniPod Mini 1st GeniPod Mini 2nd Gen
-
Most likely
Failed microdrive (the Mini's hard drive)
When the Mini's tiny hard drive (the microdrive) fails, it shows the sad iPod face or a folder icon, or makes clicking noises. Replace it with a used original microdrive, or upgrade to flash: a failed drive is the ideal time for it. Flash storage has no heads, platters or motor, so the clicking, stalling and seizing that end an old hard drive can't happen. If your old drive still reads, add our music transfer ($129) and we copy everything on it onto the new flash storage.
Replacement Microdrive (4GB)
Flash Mod Service (installed by iMods)
Replaces the hard drive with flash memory: silent, no moving parts
Flash Mod Service (installed by iMods)
Replaces the hard drive with flash memory: silent, no moving parts
-
Next most likely
Loose or damaged hard drive cable
A loose or damaged hard drive cable can make the drive click, drop out or show the sad iPod face. Unless the problem started after a repair, the cable itself is rarely the fault on the Mini: if the microdrive isn't to blame, the logic board is just as likely as the cable.
Free check first Push the cable back in first; replace it only if that does not help.
Hard Drive Cable
Hard Drive Ribbon Cable
-
Also possible
Battery too weak to spin up the hard drive
A worn battery cannot give the hard drive enough power to spin up, so the drive clicks and retries.
Free check first Connect it to a charger: that often tells whether the problem is the battery or something more serious.
Replacement Battery
Replacement Battery
-
Also possible
Damaged iPod software
The iPod's software is damaged, so it can't start properly or keeps freezing. Restoring it puts fresh software on it; a restore erases the songs on the iPod.
Free check first If it still shows up on a computer, copy your music off first, then restore it with iTunes (or Finder on a Mac with macOS Catalina or later). On the Mini 1st Gen the restore can stop at a picture of a plug: connect it to a wall charger to finish. Generic or incompatible wall chargers don't always give the iPod the right voltage: Apple's A1070 wall charger works with every model and is the ideal choice. If the restore fails, or the problem comes back, the hard drive (Mini: microdrive) is the likely fault.
iPod 3rd GeniPod 3rd Gen
-
Most likely
Failing hard drive
Repeated clicking (the click of death: click, click, whir, or grinding) or the sad iPod face usually mean the hard drive is failing. A failed drive is the ideal time for a flash upgrade: flash storage has no heads, platters or motor, so the clicking, stalling and seizing that end an old hard drive can't happen. If your old drive still reads, add our music transfer ($129) and we copy everything on it onto the new flash storage.
Replacement Hard Drive
10GB · 15GB · 20GB · 30GB · 40GB
Flash Mod Service (installed by iMods)
Replaces the hard drive with flash memory: silent, no moving parts
-
Next most likely
Loose or damaged hard drive cable
A loose or damaged hard drive cable can make the drive click, drop out or show the sad iPod face. Unless the problem started after a repair, the cable itself is rarely the fault on the 3rd Gen: if the hard drive isn't to blame, the logic board is just as likely as the cable.
Free check first Push the cable back in first; replace it only if that does not help.
Hard Drive IDE Ribbon Cable
-
Also possible
Battery too weak to spin up the hard drive
A worn battery cannot give the hard drive enough power to spin up, so the drive clicks and retries.
Free check first Connect it to a charger: that often tells whether the problem is the battery or something more serious.
Replacement Battery (All Capacities)
-
Also possible
Damaged iPod software
The iPod's software is damaged, so it can't start properly or keeps freezing. Restoring it puts fresh software on it; a restore erases the songs on the iPod.
Free check first If it still shows up on a computer, copy your music off first, then restore it with iTunes (or Finder on a Mac with macOS Catalina or later). On the 3rd Gen the restore can stop at a picture of a plug: connect it to its FireWire wall charger to finish. Generic or incompatible wall chargers don't always give the iPod the right voltage: Apple's A1070 wall charger works with every model and is the ideal choice. If the restore fails, or the problem comes back, the hard drive is the likely fault.
Stuck on Apple logo then turns off
Also searched as Apple logo appears then disappears · shows Apple logo then shuts off · shows Apple logo then turns off
It shows the Apple logo, then turns off.
Free checks first
- Still stuck on the Apple logo and shutting down while it is on a charger? Most likely the hard drive (on the 4th Gen and Photo: the drive cable first, then the drive).
- Hold the iPod up to your ear: unusual clicking patterns are a strong sign that the hard drive is failing.
- Check the hard drive's health in Diagnostic Mode: on a healthy drive the reallocated sectors (reallocs) and pending sectors read zero or close to it. A high number, or numbers that rise each time you check, mean the drive is failing; pending sectors are the sharper warning.
iPod Classic 6th and 7th GeniPod Classic 6th GeniPod Classic 7th Gen
-
Most likely
Failing hard drive
Repeated clicking (the click of death: click, click, whir, or grinding) or the red X usually mean the hard drive is failing. A failed drive is the ideal time for a flash upgrade: flash storage has no heads, platters or motor, so the clicking, stalling and seizing that end an old hard drive can't happen. If your old drive still reads, add our music transfer ($129) and we copy everything on it onto the new flash storage.
Flash Mod Service (installed by iMods)
Replaces the hard drive with flash memory: silent, no moving parts
Replacement Hard Drive 160GB (Late 2009)
Flash Mod Service (installed by iMods)
Replaces the hard drive with flash memory: silent, no moving parts
-
Next most likely
Loose or damaged hard drive cable
A loose or damaged hard drive cable can make the drive click, drop out or show the red X. Unless the problem started after a repair, the cable itself is rarely the fault on the 6th and 7th Gen: if the hard drive isn't to blame, the logic board is just as likely as the cable.
Free check first Push the cable back in first; replace it only if that does not help.
Hard Drive ZIF Ribbon Cable
-
Also possible
Battery too weak to spin up the hard drive
A worn battery cannot give the hard drive enough power to spin up, so the drive clicks and retries.
Free check first Connect it to a charger: that often tells whether the problem is the battery or something more serious.
Replacement Battery (160GB)
-
Also possible
Damaged iPod software
The iPod's software is damaged, so it can't start properly or keeps freezing. Restoring it puts fresh software on it; a restore erases the songs on the iPod.
Free check first If it still shows up on a computer, copy your music off first, then restore it with iTunes (or Finder on a Mac with macOS Catalina or later). If the restore fails, or the problem comes back, the hard drive is the likely fault.
iPod Video 5th GeniPod Video 5th Gen
-
Most likely
Failing hard drive
Repeated clicking (the click of death: click, click, whir, or grinding) or the sad iPod face usually mean the hard drive is failing. A failed drive is the ideal time for a flash upgrade: flash storage has no heads, platters or motor, so the clicking, stalling and seizing that end an old hard drive can't happen. If your old drive still reads, add our music transfer ($129) and we copy everything on it onto the new flash storage.
Flash Mod Service (installed by iMods)
Replaces the hard drive with flash memory: silent, no moving parts
-
Next most likely
Loose or damaged hard drive cable
A loose or damaged hard drive cable can make the drive click, drop out or show the sad iPod face. Unless the problem started after a repair, the cable itself is rarely the fault on the iPod Video: if the hard drive isn't to blame, the logic board is just as likely as the cable.
Free check first Push the cable back in first; replace it only if that does not help.
-
Also possible
Battery too weak to spin up the hard drive
A worn battery cannot give the hard drive enough power to spin up, so the drive clicks and retries.
Free check first Connect it to a charger: that often tells whether the problem is the battery or something more serious.
-
Also possible
Damaged iPod software
The iPod's software is damaged, so it can't start properly or keeps freezing. Restoring it puts fresh software on it; a restore erases the songs on the iPod.
Free check first If it still shows up on a computer, copy your music off first, then restore it with iTunes (or Finder on a Mac with macOS Catalina or later). If the restore fails, or the problem comes back, the hard drive is the likely fault.
iPod 4th Gen and iPod PhotoiPod 4th GeniPod Photo
-
Most likely
Loose or damaged hard drive cable
On the 4th Gen and Photo, an iPod that seems too weak to spin up its hard drive often has a hard drive cable problem. A loose or damaged hard drive cable can make the drive click, drop out or show the sad iPod face. A cable fault sounds like click, whir; a failing drive sounds more like click, click, whir.
Free check first Clean the hard drive cable's contacts with 99% isopropyl alcohol (IPA) and re-seat it first; if that fails, it's likely a bad hard drive (our Hard Drive Repair Service is probably the best first option).
Hard Drive IDE Ribbon Cable
Hard Drive IDE Ribbon Cable
-
Next most likely
Failing hard drive
Repeated clicking (the click of death: click, click, whir, or grinding) or the sad iPod face usually mean the hard drive is failing. Flash storage is the silent alternative to a new drive. On the 4th Gen and Photo we can often fix the hard drive without replacing it, and in most cases all songs are saved.
Hard Drive Repair Service
Mail it in: we repair your drive, and in most cases your songs are saved
Hard Drive Repair Service
Mail it in: we repair your drive, and in most cases your songs are saved
Flash Mod Service (installed by iMods)
Replaces the hard drive with flash memory: silent, no moving parts
Replacement Hard Drive
20GB · 30GB · 40GB · 60GB
Flash Mod Service (installed by iMods)
Replaces the hard drive with flash memory: silent, no moving parts
-
Also possible
Battery too weak to spin up the hard drive
A worn battery cannot give the hard drive enough power to spin up, so the drive clicks and retries. On the 4th Gen and Photo this is rarely the answer: far more often it is the hard drive cable. On the 4th Gen and Photo this is rarely the cause: the hard drive cable is far more often the fault.
Free check first Connect it to a charger: that often tells whether the problem is the battery or something more serious. If it still clicks and restarts on the charger, the battery is very unlikely to be the problem. If it still clicks and restarts on the charger, the battery is very unlikely to be the problem.
Replacement Battery (All Capacities)
Replacement Battery
-
Also possible
Damaged iPod software
The iPod's software is damaged, so it can't start properly or keeps freezing. Restoring it puts fresh software on it; a restore erases the songs on the iPod.
Free check first If it still shows up on a computer, copy your music off first, then restore it with iTunes (or Finder on a Mac with macOS Catalina or later). On the 4th Gen and iPod Photo the restore can stop at a picture of a plug: connect it to a wall charger to finish. Generic or incompatible wall chargers don't always give the iPod the right voltage: Apple's A1070 wall charger works with every model and is the ideal choice. If the restore fails, or the problem comes back, the hard drive cable, then the hard drive, is the likely fault (our Hard Drive Repair Service is probably the best first option).
iPod Mini 1st and 2nd GeniPod Mini 1st GeniPod Mini 2nd Gen
-
Most likely
Failed microdrive (the Mini's hard drive)
When the Mini's tiny hard drive (the microdrive) fails, it shows the sad iPod face or a folder icon, or makes clicking noises. Replace it with a used original microdrive, or upgrade to flash: a failed drive is the ideal time for it. Flash storage has no heads, platters or motor, so the clicking, stalling and seizing that end an old hard drive can't happen. If your old drive still reads, add our music transfer ($129) and we copy everything on it onto the new flash storage.
Replacement Microdrive (4GB)
Flash Mod Service (installed by iMods)
Replaces the hard drive with flash memory: silent, no moving parts
Flash Mod Service (installed by iMods)
Replaces the hard drive with flash memory: silent, no moving parts
-
Next most likely
Loose or damaged hard drive cable
A loose or damaged hard drive cable can make the drive click, drop out or show the sad iPod face. Unless the problem started after a repair, the cable itself is rarely the fault on the Mini: if the microdrive isn't to blame, the logic board is just as likely as the cable.
Free check first Push the cable back in first; replace it only if that does not help.
Hard Drive Cable
Hard Drive Ribbon Cable
-
Also possible
Battery too weak to spin up the hard drive
A worn battery cannot give the hard drive enough power to spin up, so the drive clicks and retries.
Free check first Connect it to a charger: that often tells whether the problem is the battery or something more serious.
Replacement Battery
Replacement Battery
-
Also possible
Damaged iPod software
The iPod's software is damaged, so it can't start properly or keeps freezing. Restoring it puts fresh software on it; a restore erases the songs on the iPod.
Free check first If it still shows up on a computer, copy your music off first, then restore it with iTunes (or Finder on a Mac with macOS Catalina or later). On the Mini 1st Gen the restore can stop at a picture of a plug: connect it to a wall charger to finish. Generic or incompatible wall chargers don't always give the iPod the right voltage: Apple's A1070 wall charger works with every model and is the ideal choice. If the restore fails, or the problem comes back, the hard drive (Mini: microdrive) is the likely fault.
iPod 3rd GeniPod 3rd Gen
-
Most likely
Failing hard drive
Repeated clicking (the click of death: click, click, whir, or grinding) or the sad iPod face usually mean the hard drive is failing. A failed drive is the ideal time for a flash upgrade: flash storage has no heads, platters or motor, so the clicking, stalling and seizing that end an old hard drive can't happen. If your old drive still reads, add our music transfer ($129) and we copy everything on it onto the new flash storage.
Replacement Hard Drive
10GB · 15GB · 20GB · 30GB · 40GB
Flash Mod Service (installed by iMods)
Replaces the hard drive with flash memory: silent, no moving parts
-
Next most likely
Loose or damaged hard drive cable
A loose or damaged hard drive cable can make the drive click, drop out or show the sad iPod face. Unless the problem started after a repair, the cable itself is rarely the fault on the 3rd Gen: if the hard drive isn't to blame, the logic board is just as likely as the cable.
Free check first Push the cable back in first; replace it only if that does not help.
Hard Drive IDE Ribbon Cable
-
Also possible
Battery too weak to spin up the hard drive
A worn battery cannot give the hard drive enough power to spin up, so the drive clicks and retries.
Free check first Connect it to a charger: that often tells whether the problem is the battery or something more serious.
Replacement Battery (All Capacities)
-
Also possible
Damaged iPod software
The iPod's software is damaged, so it can't start properly or keeps freezing. Restoring it puts fresh software on it; a restore erases the songs on the iPod.
Free check first If it still shows up on a computer, copy your music off first, then restore it with iTunes (or Finder on a Mac with macOS Catalina or later). On the 3rd Gen the restore can stop at a picture of a plug: connect it to its FireWire wall charger to finish. Generic or incompatible wall chargers don't always give the iPod the right voltage: Apple's A1070 wall charger works with every model and is the ideal choice. If the restore fails, or the problem comes back, the hard drive is the likely fault.
Started after a repair or part swap
It started sticking at the Apple logo after the iPod was opened.
iPod Classic 6th and 7th GeniPod Classic 6th GeniPod Classic 7th Gen
-
Most likely
Hard drive cable not fully in, or a latch left open
After the iPod has been opened, a hard drive cable that isn't pushed fully in, or a drive or cable latch left open, stops the drive from working.
Free check first Open it again, push the hard drive cable fully in and close every latch.
-
Next most likely
Loose or damaged hard drive cable
A loose or damaged hard drive cable can make the drive click, drop out or show the red X. Unless the problem started after a repair, the cable itself is rarely the fault on the 6th and 7th Gen: if the hard drive isn't to blame, the logic board is just as likely as the cable.
Free check first Push the cable back in first; replace it only if that does not help.
Hard Drive ZIF Ribbon Cable
-
Also possible
A connector not seated after the repair
After a battery or part swap, a connector that is not fully seated can leave the iPod dead or half-working. We can also look at it: the free diagnostic finds the issue and whether it can be fixed without new parts.
Free check first Open it again and push every connector you touched fully back in.
iPod Video 5th GeniPod Video 5th Gen
-
Most likely
Hard drive cable not fully in, or a latch left open
After the iPod has been opened, a hard drive cable that isn't pushed fully in, or a drive or cable latch left open, stops the drive from working.
Free check first Open it again, push the hard drive cable fully in and close every latch.
-
Next most likely
Loose or damaged hard drive cable
A loose or damaged hard drive cable can make the drive click, drop out or show the sad iPod face. Unless the problem started after a repair, the cable itself is rarely the fault on the iPod Video: if the hard drive isn't to blame, the logic board is just as likely as the cable.
Free check first Push the cable back in first; replace it only if that does not help.
-
Also possible
A connector not seated after the repair
After a battery or part swap, a connector that is not fully seated can leave the iPod dead or half-working. We can also look at it: the free diagnostic finds the issue and whether it can be fixed without new parts.
Free check first Open it again and push every connector you touched fully back in.
iPod 4th Gen and iPod PhotoiPod 4th GeniPod Photo
-
Most likely
Hard drive cable not fully in, or a latch left open
After the iPod has been opened, a hard drive cable that isn't pushed fully in, or a drive or cable latch left open, stops the drive from working.
Free check first Open it again, push the hard drive cable fully in and close every latch.
-
Next most likely
Loose or damaged hard drive cable
On the 4th Gen and Photo, an iPod that seems too weak to spin up its hard drive often has a hard drive cable problem. A loose or damaged hard drive cable can make the drive click, drop out or show the sad iPod face. A cable fault sounds like click, whir; a failing drive sounds more like click, click, whir.
Free check first Clean the hard drive cable's contacts with 99% isopropyl alcohol (IPA) and re-seat it first; if that fails, it's likely a bad hard drive (our Hard Drive Repair Service is probably the best first option).
Hard Drive IDE Ribbon Cable
Hard Drive IDE Ribbon Cable
-
Also possible
A connector not seated after the repair
After a battery or part swap, a connector that is not fully seated can leave the iPod dead or half-working. We can also look at it: the free diagnostic finds the issue and whether it can be fixed without new parts.
Free check first Open it again and push every connector you touched fully back in.
iPod Mini 1st and 2nd GeniPod Mini 1st GeniPod Mini 2nd Gen
-
Most likely
Hard drive cable not fully in, or a latch left open
After the iPod has been opened, a hard drive cable that isn't pushed fully in, or a drive or cable latch left open, stops the drive from working.
Free check first Open it again, push the hard drive cable fully in and close every latch.
-
Next most likely
Loose or damaged hard drive cable
A loose or damaged hard drive cable can make the drive click, drop out or show the sad iPod face. Unless the problem started after a repair, the cable itself is rarely the fault on the Mini: if the microdrive isn't to blame, the logic board is just as likely as the cable.
Free check first Push the cable back in first; replace it only if that does not help.
Hard Drive Cable
Hard Drive Ribbon Cable
-
Also possible
A connector not seated after the repair
After a battery or part swap, a connector that is not fully seated can leave the iPod dead or half-working. We can also look at it: the free diagnostic finds the issue and whether it can be fixed without new parts.
Free check first Open it again and push every connector you touched fully back in.
iPod 3rd GeniPod 3rd Gen
-
Most likely
Hard drive cable not fully in, or a latch left open
After the iPod has been opened, a hard drive cable that isn't pushed fully in, or a drive or cable latch left open, stops the drive from working.
Free check first Open it again, push the hard drive cable fully in and close every latch.
-
Next most likely
Loose or damaged hard drive cable
A loose or damaged hard drive cable can make the drive click, drop out or show the sad iPod face. Unless the problem started after a repair, the cable itself is rarely the fault on the 3rd Gen: if the hard drive isn't to blame, the logic board is just as likely as the cable.
Free check first Push the cable back in first; replace it only if that does not help.
Hard Drive IDE Ribbon Cable
-
Also possible
A connector not seated after the repair
After a battery or part swap, a connector that is not fully seated can leave the iPod dead or half-working. We can also look at it: the free diagnostic finds the issue and whether it can be fixed without new parts.
Free check first Open it again and push every connector you touched fully back in.
Not sure — free diagnostic
Mail us your iPod and we test it and send you a free repair quote. If you don't like the price, we ship it back at our expense.
Free