Replacement housing or trim part for iPod Mini 1st Generation. Use it to restore fit, finish, color, case alignment, or visible damage rather than to fix an internal electronics fault.
Product Overview
Choose this housing listing to restore the visible fit, finish, or mounting hardware on the iPod Mini 1st Generation.
Use the Compatible Variants table below to confirm capacity, color, or order-number fitment.
This is a fit-and-finish part, so choose it by physical damage, color, part shape, and missing hardware rather than by an electrical symptom.
What Is Included
Quick Buying Check
Buy this when
- Plastic trim damage: Use this bottom bezel check for cracked, missing, stained, chipped, or loose white plastic trim after confirming internal electronics symptoms belong elsewhere.
- The original part is cracked, scratched, dented, bent, missing, loose, or cosmetically worn.
- The model, color, model-specific fitment, and capacity family match this listing.
Specifications & Fitment
Part Details
| Detail | Value |
|---|---|
| Model Number | A1051 |
| EMC | EMC 1984 |
| Condition | Used — factory original Apple part. Normal cosmetic wear expected. |
| Material | Plastic |
Compatible Variants
| Order Number | Capacity | Color | Case | Compatible | Notes |
|---|---|---|---|---|---|
| M9436LL/A | 4GB | Blue | — | Yes | — |
| M9437LL/A | 4GB | Gold | — | Yes | — |
| M9434LL/A | 4GB | Green | — | Yes | — |
| M9435LL/A | 4GB | Pink | — | Yes | — |
| M9160LL/A | 4GB | Silver | — | Yes | — |
Cosmetic Failure Signs — When to Replace
This housing is a cosmetic part — it does not change how the iPod plays, charges, or syncs. Replace it when the damage is physical:
Not every buyer here is fixing damage: matching the original finish after another repair, restoring a gift or keepsake iPod to clean condition, and finishing a refreshed shell while the case is already open are just as common.
Do Not Buy / Problems This Housing Part Does Not Fix
| Situation | Start here instead |
|---|---|
| You have an iPod Mini 2nd Generation — different bezel design | This is a different model — check your order number and generation before ordering. |
| You have a full-size hard-drive iPod with a different case design. | This is a different model — check your order number and generation before ordering after matching the exact symptom and part family. |
| The only problem is an internal electronic symptom with no physical damage to this part | Start with the diagnosis that matches your symptom — not a housing part. |
| The issue is charging, audio, storage, display, or controls rather than fit, finish, or visible housing damage | Start with the hard drive, flash storage, or drive cable check. |
| The replacement would not match the model-specific fitment, color, or capacity family you are repairing | Confirm the exact model, capacity, connector, and case variant before ordering. |
Install Overview
Before You Start
Set Hold to locked (orange bar visible) before opening. Confirm the model and variant before opening the iPod.
Treat case opening as the highest handling risk. Work around the seams gently and stop if the shell, clips, or internal stack resist.
Do not pull the halves apart or side-load board sockets. Reseat nearby ribbons and connectors before blaming a replacement housing part.
Confirm thickness, color, screw points, and nearby hardware alignment before pressing the case fully closed.
Repair steps
Documented repair-procedure steps for replacing the housing part on this model (from teardown guides; confirm against your unit before starting):
- Carefully insert a small flathead screwdriver or Jimmy in the seam between the metal casing and white plastic bottom. Use the screwdriver to pry up the white plastic bottom bezel. Be careful not to damage the soft plastic with your screwdriver.
- Carefully slide the iPod out of its casing by pushing on the logic board near the bottom edge of the click wheel.
Repair Guide
Repair guide summary: iPod Mini Bottom Bezel Replacement.
Show all 3 installation steps
Carefully slide a small flathead screwdriver or Jimmy into the seam between the metal casing and white plastic bottom. Lever up the white bottom bezel, taking care not to damage the soft plastic.
A small pair of snap-ring pliers is the best tool to take out the metal retaining bracket. You can also lever out the metal retaining bracket beneath the bottom bezel with a flathead screwdriver. Release the bracket by pressing in the corner metal arms first.
Lift the released bracket away and set it aside.
After This Repair
| Check | What to do |
|---|---|
| Check trim fit | Confirm the trim sits flush and the port or opening is centered before final closure. |
| Still not fitting cleanly? | Recheck model-specific fitment, screw seating, and nearby clips before forcing the trim into place. |
Worth Knowing
- Bottom bezel houses the 30-pin dock connector opening.
- Must be removed to slide internal components out of the aluminum tube.
- This small white bottom trim frames the 30-pin dock connector opening.
Frequently Asked Questions
How do I choose the right cosmetic part?
Match the model generation first, then confirm capacity 4GB, clip layout, and nearby hardware before ordering.
Will this fix internal electronics symptoms?
No. Housing and trim parts are for fit, finish, color, alignment, or visible damage. Diagnose power, storage, audio, screen, and control faults separately.
How do I confirm this is the right exterior part?
Match the exact iPod Mini 1st Generation model, visible part shape, color or finish goal, and any capacity or model-specific fitment note before ordering Replacement Plastic Dock Port Bezel.
Why people land on this part
Also searched as: iPod mini 1st generation housing part, iPod mini 1st generation plastic dock port bezel replacement, iPod mini 1st Generation housing, bottom cap, iPod mini plastic bottom bezel, iPod mini end cap, white end caps, iPod mini dock connector bezel.
Fitment wording people compare
- aluminum tube damage
- metal dock-port bracket not included
